SVC on Twitter    SVC on Facebook    SVC on LinkedIn


10 Tips for Better AV Systems

We polled manufacturers, integrators, and end users to help identify lingering pain points and asked them for quick solutions and insights. Depending on what you're working on, you should be able to find a handful of these tips worth clipping out and stuffing in your back pocket for future reference.

As if we can reduce the many technical issues that AV designers, users, installers, and integrators regularly face to a list of 10! Most of you probably tackle that many hurdles the first day working on a new AV system. But technologies evolve, acronyms breed and spread, and sometimes it's nice just to remind ourselves that if there's a question about a new or existing AV solution, an AV professional has probably thought up a tip, gadget, list, rule-of-thumb, you name it, to help handle the situation.

We polled manufacturers, integrators, and end users to help identify lingering pain points and asked them for quick solutions and insights. Some deal with new technology, some with existing systems, and they all run the gamut from audio to video to signal management.

Will they solve all your AV problems? Of course not. But depending on what you're working on today, you should be able to find a handful of these tips worth clipping out and stuffing in your back pocket for future reference. Go ahead. Get your scissors. We'll wait.

Dan Daley is a freelance AV writer based in Nashville, Tenn. Special thanks for their help with these tips to AV pros at Alcorn McBride, AMX, AVI-SPL, Belden, Crestron, Extron, and Key Digital, as well as Jeff Boccaccio of DPL Labs and Mary Meeker of MEM Systems.


QSC's PowerLight 3 Series Class-D amplifiers

Zap! Class-D Amps and Static

New Class-D switching amplifiers have high impedance outputs that are very efficient, allowing the circuits to be very small. But they are also high impedance circuits and are thus susceptible to static buildup and resulting circuit damage.

However, it's easy to protect against static charge damage. Simply connect three metal oxide varistors (MOV) to each amplifier output. One MOV connects across the pair of speaker wires, while the others connect each wire to the ground. These should all be installed at or near the amplifier, not out in the field. This should render your amplifier relatively immune the next time the weather gets stormy.

Putting the 'You' in UTP

Most installers know that unshielded twisted pair (UTP) cabling such as Cat-5/6 can be used for more than just Ethernet connectivity. Here are a few other ways to exploit the benefits of UTP in an AV system:

¦ Assuming it's already in place, use UTP cable for serial or IR control (and even low voltage power) instead of pulling a new specialized cable for control.

¦ Use UTP to transmit audio and video in addition to power and control. Just be aware some manufacturers require that their proprietary (and much more expensive) UTP cable be used instead of standard cabling.

¦ Future-proof an AV installation with UTP. Always pull it back to a centralized patch point in order to maximize flexibility in the future and think about how you might use it. If it will be used for Ethernet, make sure the run isn't more than 100 meters (328 feet).

It may already be old hat to mention this, but always be careful when handling UTP cable to maintain its performance characteristics. Don't bend, crimp, staple, stretch, or twist UTP cable–the end users will thank you.

When Cat-5 Meets the Elements

Category-5 cable is pretty robust stuff, but extreme climate conditions, such as high or fluctuating humidity and/or condensation levels, can cause significant signal degradation at the termination points over time. There is a fix, however.

To protect Cat-5 cabling against the elements, consider this relatively simple solution: At one end of the wire run, pressure-terminate the cable to a transmitting balun. At the other end, use a matrix switcher with a receiving balun. Over time, if the cable begins to become affected by the environment and the signal degrades, the transmit/receive balun combination, which has been monitoring the cable run, senses this deterioration as a lengthening of the cable. Such deterioration would produce the same degradation symptoms as humidity or condensation. The combination then auto-compensates for both signal strength and equalization, maintaining a good connection.


Balun/transmitter from Key Digital

HDMI: Troubleshooting On The Fly

HDMI is the bane of a pro AV install's existence. But an understanding of its basics can provide you with enough information to do simple troubleshooting without hauling around expensive test equipment. In fact, just understanding the startup process might be enough to keep you out of harm's way.

The system starts by sending a control voltage from the source to the display. Upon receiving this "start" voltage, the display sends back a response called a hot plug. Once this arbitration is completed, the source requests all extended display identification data (EDID) in order to match its video settings to the display's settings. Then HDCP (high-bandwidth digital content protection) is launched. Without all of these elements, your screen will be blank.

If you have a blank screen, step one is to shut everything down. Second, you need a DVD player with no disc inside (not a Blu-ray player)–turn on the display first, then the DVD player. If the display shows any response when the DVD player starts up, it means your start voltage made it through.

Next, see if the DVD logo appears. If it does, insert a DVD disc and start again. If after you fire up the player the disc plays, then you probably have a video integrity issue; if not, you most likely are dealing with an HDCP issue.


Keep a regular DVD player handy to troubleshoot HDMI issues

More Than Meets The Eye With HDMI

Installing HDMI distribution systems is very different from analog AV. Many AV professionals don't realize there are many more layers to an HDMI signal than just AV. As a matter of fact, there are 19 wires altogether in HDMI, including two-way embedded data pathways such as HDCP content protection, EDID resolution management, and CEC controls. Those embedded communication streams add complexity that often creates issues with system performance and reliability.

Every source component can accept a specific number of HDCP authentication keys. Manufacturers do not specify key limitations for their equipment, so if a source signal is inadvertently distributed to more displays than it can support, the source component automatically turns off. To avoid such an error, it's important to run an HDCP check to determine the number of keys each source can accept and then configure the system accordingly.

Displays send EDID data so that sources will output the optimal signal resolution. However, in a distribution system where displays have not been standardized, inconsistencies are common. Native resolutions for different displays vary, and this may cause sources to output at lower resolutions than desired. EDID information should be managed to optimize output signal resolution or determine the best common resolution for all sources and displays.

To diagnose and troubleshoot digital systems quickly and reliably, look for solutions that come with or offer robust installation software to manage EDID and to run HDCP and data rate checks.


Crestron's DigitalMedia platform uses the company's DM Tools setup software

Screen Blank? Could Be an EDID Issue

Extended display identification data (EDID) exchange is a standardized way for a display to communicate its capabilities, such as its native resolution, to an attached source device, which then generates the necessary video characteristics to match the needs of the display. When successful, EDID data exchange maximizes functional compatibility between devices, helping to ensure optimal image quality as well as overall system reliability.

However, this data exchange often is not successful. The implementation of EDID for display devices varies widely, and in some cases, displays lack EDID information altogether. Such inconsistencies can cause operational issues ranging from overscan and resolution problems, to a display device not displaying an image at all. But it's not always clear that EDID is the problem.

To help determine whether EDID incompatibility may be the cause of an image display issue, a simple software application (free utilities can be downloaded online, or manufacturers often offer them with related hardware) can be used to directly view the contents of the EDID information from a display device. Connecting the display to a computer allows you to access the EDID and store it in the computer's Windows registry. The software then accesses the EDID settings in the registry and lets you examine their contents.

To solve an EDID compatibility problem, use an EDID emulation device (manufacturers such as Extron and others make them). Such a device manages EDID data at the source and can be installed between source and display to communicate the EDID that the source needs in order to provide the proper video output. The devices generate emulated EDID based on a user-selected resolution and refresh rate, or EDID that was captured and stored from the display device. The source then generates the output accordingly, which is passed through the device to the display.


Extron 101D Emulator comes with management software

Interpreter Wanted for Digital Audio Devices

Digital I/O is the norm in most audio systems these days. Many devices incorporate a mix of analog and digital signals. But interpreting signal levels on these components can be confusing, mainly because the same meters are typically used for both signal types. To make sense of the information on a digital mixer's main output meter, first you have to determine which of the outputs is being used–analog or digital. Then, if the device is analog, determine its maximum level. This can be found in the device manual's specifications section.

A digital meter is typically referenced in dBFS (also known as digital full scale), while analog metering is measured in dBu increments. So for example, if it were established that the console's maximum analog output level is +18 dBu, that would equate to 0 dBFS on a digital meter. When meters are pulling double-duty as both analog and digital meters, you have to find out from the console's documentation what the maximum analog output level is; this would be equivalent to 0 dBu's on the console in the digital domain. You can now proceed confidently with an understanding of what the meter is telling you about the output level of either the analog or digital signals from the console.

Screen Failure in Digital Signage Systems

A common failure point in digital signage systems is the power supply for the display screen. Often this results from a display network owner's policy of shutting down power to all their screens each night and restoring power each morning using the building circuit breakers. Doing so repeatedly is hard on power supplies and often leads to a breakdown.

To prevent such problems, pay attention to the power-up sequence of a signage network. The typical display screen is 200 to 300 watts or 2 to 3 amps. This allows for, at most, five screens per 20-amp power circuit. Setting the flat-panels' internal on-screen display (OSD) power-up features at intervals five seconds apart will allow the power to be adequately and safely sequenced.

When possible, use the internal scheduling found in the OSD of some manufacturers' screens or an RS-232-based control system that allows for managing the power on a schedule. Controlling power in this method allows you to put a screen in standby mode, thus reducing power consumption to less than a watt per screen. If the installation comprises 300 or more screens and doesn't need to be displaying signage eight hours a day, that's a savings of up to 2,400 watts of power per day, while at the same time enabling quick and efficient startup in the mornings.

1 2 Next
Browse Back Issues
  August 2014 Sound & Video Contractor Cover July 2014 Sound & Video Contractor Cover June 2014 Sound & Video Contractor Cover May 2014 Sound & Video Contractor Cover April 2014 Sound & Video Contractor Cover March 2014 Sound & Video Contractor Cover  
August 2014 July 2014 June 2014 May 2014 April 2014 March 2014