SVC on Twitter    SVC on Facebook    SVC on LinkedIn

Related Articles


Audio-Technica BP896cW and BP892cW Review

Nov 9, 2009 12:00 PM, By John McJunkin

Two tiny mics that effectively capture the entire frequency spectrum.

   Follow us on Twitter    

Audio-Technica BP892cW

Audio-Technica BP892cW

Lavalier and headworn mics are central, important staples in the toolkits of contractors and integrators the world over, so any advancement in the quality of these important tools is greeted with pleasure by the professionals who use them. These mics can be used nearly interchangeably, so it made sense to evaluate one of each from Audio-Technica's latest array of offerings. While reductions in the size of microphones have slowed in recent years, the audio quality they exhibit continues to increase, and that is precisely what Audio-Technica (A-T) has achieved with these new mics. I evaluated these mics by applying them in real-world situations, and I discovered that they are very worthy of consideration. This is no surprise, considering that Audio-Technica has a reputation for constant new development and improvement.

I evaluated the BP896cW MicroPoint lavalier mic and BP892cW Microset headworn mic, along with Audio-Technica's Artist Elite AEW-R4100 receiver and AEW-T1000 UniPak transmitter. The BP896cW MicroPoint is Audio-Technica's latest lavalier offering, and its smallest yet—keeping pace with the state of the art in lav mics. The actual microphone element is 0.43in. long and 0.1in. in diameter. This is a truly tiny microphone, so I was very curious to see if A-T could pull off quality transduction with such a small package. The two-conductor shielded cable that connects it to either a power module or wireless transmitter is 1.4 meters long. More importantly, it is only 1.6mm in diameter. The mic's cable is available with A-T's 4-pin connector for use with UniPak wireless systems; a Lemo connector or locking 3.5mm connector for use with Sennheiser wireless systems; a TA4F-type connector for use with Shure wireless systems; a TA5F-type connector for use with Lectrosonics wireless systems; or an unterminated version so contractors can make the determination themselves. All of these versions are available in both black and beige.

The lav mic is a fixed-charge back-plate, permanently polarized condenser with an omnidirectional pattern. Frequency response is published as 20Hz to 20kHz, with a UniSteep high-pass filter available in the wired version. This filter has a corner frequency of 80Hz and slope of 18dB/octave, and it is used to reduce popping from plosives, wind noise, and low-frequency ambience. The frequency response is quite flat, with the notable exception of a smooth bulge from 10kHz to 20kHz, centered at approximately 15kHz and with a maximum increase in sensitivity of approximately 3dB. This is a very welcome nonlinearity in that it contributes nicely (and subtly) to the air captured by the mic. Impedance is rated at 250Ω, and the mic is rated for a maximum input sound level of 135dB SPL, which is plenty for a lavalier mic. The mic's output signal is quiet with its signal-to-noise ratio published as 63dB. It's quite forgiving in terms of its phantom-power requirement, operating on a range from 11V to 52V at 2mA, so if a contractor wishes to provide phantom power, tolerance is not particularly critical. For wired applications, the mic ships with an AT8539 power module to provide the required phantom power.

The mic also ships with an array of accessories, including two AT8157 windscreens; six element covers (two of each in white, beige, and black); a viper clip base; a clothing clip base; three black single mic holders; two black double mic holders; a carrying case; and a belt clip for the wired version. Nearly every conceivable placement scheme can be accomplished with the included clips.

The BP892cW is a headworn mic featuring the same condenser element as the BP896cW. It is literally the same element, so all technical specifications are identical. This mic comprises a simple boom suspended by an earpiece. The boom is 3.87in. long and 0.04in. in diameter. It almost appears frail considering the slender boom, but the metal from which it is made is substantial yet easily molded to get the mic close to the wearer's mouth. A moisture-blocking ring is placed on the boom. Although getting the mic element in a good position is easy, it's not particularly critical because the element is omnidirectional, and as long as it's placed within a couple of inches of the user's mouth, a clear, highly intelligible signal is captured. I have been a user of older A-T mics (both lavalier and headworn), and I was pleasantly surprised with the leap in quality that this mic delivered.

Acceptable Use Policy
blog comments powered by Disqus

Browse Back Issues
  January 2015 Sound & Video Contractor Cover December 2014 Sound & Video Contractor Cover November 2014 Sound & Video Contractor Cover October 2014 Sound & Video Contractor Cover September 2014 Sound & Video Contractor Cover August 2014 Sound & Video Contractor Cover  
January 2015 December 2014 November 2014 October 2014 September 2014 August 2014